济南木工机械磨刀机的几点介绍-ag捕鱼平台

当前位置:捕鱼游戏主页 > 新闻资讯 >
product center
捕鱼娱乐平台的产品中心
联系捕鱼娱乐平台

济南骏捷数控设备有限公司

销售总机:师楠 18866899200

固定电话:0531—69989273

销售一部:师经理 13001727679

销售二部:谢经理 18766192210

地址:山东省济南市天桥区桑梓店镇绕城高速北200米海风产业园713号

新闻资讯
济南木工机械磨刀机的几点介绍
发布时间:2016-12-26 16:46:49     浏览次数:1221次

1.济南木工机械专家提醒,在磨刀机起动前,可用手转动磨刀盘,然后合上电源开关,检查磨刀盘的旋转有无摆动现象,若有摆动,应修理校正。ji'nan woodworking machinery experts remind, in the grinding machine before starting hand rotating knife disc, and then turn on the power switch, check the rotation of the disc knife there is no swing phenomenon, if there is a swing, correction should be repaired.

2.济南木工机械磨刀机,在起动前,应先在贮料槽内调好以180#或2004金刚砂粉40%,机油30%,煤油30%的混合物作为涂在磨刀盘上的磨料。ji'nan woodworking machinery grinder, before starting, first in the material storage in 180# or 2004 emery powder 40%, 30% oil tank, a mixture of kerosene 30% as the abrasive disc on the knife.
 
3.把钝刀片放在热碱水中洗净,刀齿向上,安装在磨刀夹上,用挂钩在支架上挂着。blunt blade in hot alkali water to wash, knife, knife is installed on the clamp, hook hanging on the bracket.

4.济南木工机械起动磨刀机在研磨时,将刀片靠在磨刀盘上不停地左、右摆动。压力不宜过大,并随时涂上磨料,用力必须均匀,不应将刀片磨成厚薄不均匀、中间有凸的形状。ji'nan woodworking machinery starting in grinding machine grinding, the blade on the knife disc incessantly on the left and right swing. the pressure is too large, and be coated with abrasive, force should be uniform, should not be grinding uneven thickness, blade convex middle shape.

5.在研磨中,注意勿使刀片产生过热现象,以免退火。磨锐一把刀片一般需25-40秒钟,应以磨锐为准。in grinding, pay attention not to make the blade overheating, so as to avoid annealing. sharpening a blade generally takes 25-40 seconds, should be sharpened to prevail.

6.磨削后的刀片,用平尺检查刀片不平度,允许有不大于0. 035毫米的最大凹面值,但不允许有凸面产生,并用手指在刃口上轻轻横刮几下,试其是否有磨锋利的感觉。 after grinding the blade, with a flat blade inspection roughness, allow a maximum of not more than 0.035 mm concave value, but does not allow the convex, and fingers in the edge gently scraping a few cross, test whether there is a sharp feeling.

7.刀片磨锐后,用煤油或柴油洗净刀片上的金刚砂。after sharpening the blade, wash the carborundum on the blade with kerosene or diesel oil.

8.如果济南木工机械刀片经数次研磨后,刀片平面仍有凸面,则应检查磨刀盘有无凹面;如有凹面,可用油石将其修平。if ji'nan woodworking machinery blade by several after grinding blade plane is convex, it should check the grinding plate without concave; if there is concave, the whetstone available hsiuping.

9.如果济南木工机械磨刀过程中发现刀片磨不均匀,应耐心研磨几次,注意不要急躁,以免损坏磨刀盘。 if the blade grinding uneven ji'nan woodworking machinery grinding process, grinding should be patient several times, not impatient, so as not to damage the grinding wheel.